RECENTLY VIEWED
Skip to main content
CRL Closed Cell Backer Rod is a round, flexible, closed cell polyethylene foam with an exterior "skin" used as a backing and thickness control device for elastomeric and other cold-applied sealants. The Backer Rod becomes an integral part of the joint into which it is installed, and therefore is available in a range of diameters to accommodate joints from 3/16" to 1-5/8" (5 to 41 mm). It limits the depth of the sealant, thereby preventing excessive use of the sealant, which promotes proper joint design. Because the sealant will not bond to the "skin" of the rod, it can stretch and recover with joint movement, with minimal stress being put on the points of adhesion to the substrate.
CRL Closed Cell Backer Rod will not absorb water or wick water to joint walls, which could cause adhesive failure. It is compatible with cold-applied sealants, and its round shape promotes the preferred "hourglass" shape for joint sealants. It withstands hot and cold temperature extremes from -45 degree to 160 degreeF (-43 degree to 71 degreeC).
CRL Closed Cell Backer Rod is chemically inert, and resistant to oils, gasoline, and solvents. It will not stain or "bleed" into sealant material. Backer Rod is typically used in expansion/control joints where cold-applied sealants are used. These joints would normally be found in curtain walls, construction partitions, precast panels, parking decks, door and window frame perimeters, coping, floor and deck joints, horizontal traffic joints, and building rehabilitation projects.
Proper size selection of CRL Closed Cell Backer Rod is important as it controls the depth of the sealant bead. It must be approximately 25% wider than the joint to fit tightly, and function as a bond breaker to prevent bottom side adhesion of the sealant. Always install using a blunt tool or roller. Cat. No. SBRR Backer Rod Roller is designed specifically for the smooth installation of all types of backer rods.
Product Warning:
NOTE: Do not tear, puncture, crease, over compress or stretch during insertion. Always use the correct size Backer Rod for the particular application. Refer to the size selection chart. Do not use with hot-applied sealants or hot melt adhesives where their surface temperature is over 160 degreeF (71 degreeC).
DK Hardware Professional Tax Exempt? Net 30? - DK Net Terms
Roll over image to zoom in
Product Features
Product Overview
Related Videos
Reviews
Questions & Answers
CRL EF34C 3/4" Closed Cell Backer Rod - 100' Roll Gray
Item #: EF34C by CR Laurence
33 reviews
QTY
–
+
+ Add to Wishlist
Buy in Bulk & Save - See How Watch Now
30 Days Easy Return. We are the largest supplier of the most adaptable, personalized hardware in the industry. We work hard to ensure you're satisfied with our products.
Features
- Allows Easy Control of Sealant Application Thickness
- Compatible with All Cold-Applied Sealants
- Won't Adhere to Sealants; No Bond Breaker Needed
Diameter of Rod
3/4 in (19 mm)
Feet per Roll
100 ft (30.5 m)
Rod Diameter
3/4" (19 mm)
Roll Length
100' (30.5 m)
Diameter
3/4
Finish
GRAY
Type
Closed Cell
Finish/Color
Gray
Roll Length (Feet)
100
Product Overview
CRL Closed Cell Backer Rod is a round, flexible, closed cell polyethylene foam with an exterior "skin" used as a backing and thickness control device for elastomeric and other cold-applied sealants. The Backer Rod becomes an integral part of the joint into which it is installed, and therefore is available in a range of diameters to accommodate joints from 3/16" to 1-5/8" (5 to 41 mm). It limits the depth of the sealant, thereby preventing excessive use of the sealant, which promotes proper joint design. Because the sealant will not bond to the "skin" of the rod, it can stretch and recover with joint movement, with minimal stress being put on the points of adhesion to the substrate.
CRL Closed Cell Backer Rod will not absorb water or wick water to joint walls, which could cause adhesive failure. It is compatible with cold-applied sealants, and its round shape promotes the preferred "hourglass" shape for joint sealants. It withstands hot and cold temperature extremes from -45 degree to 160 degreeF (-43 degree to 71 degreeC).
CRL Closed Cell Backer Rod is chemically inert, and resistant to oils, gasoline, and solvents. It will not stain or "bleed" into sealant material. Backer Rod is typically used in expansion/control joints where cold-applied sealants are used. These joints would normally be found in curtain walls, construction partitions, precast panels, parking decks, door and window frame perimeters, coping, floor and deck joints, horizontal traffic joints, and building rehabilitation projects.
Proper size selection of CRL Closed Cell Backer Rod is important as it controls the depth of the sealant bead. It must be approximately 25% wider than the joint to fit tightly, and function as a bond breaker to prevent bottom side adhesion of the sealant. Always install using a blunt tool or roller. Cat. No. SBRR Backer Rod Roller is designed specifically for the smooth installation of all types of backer rods.
Product Warning:
NOTE: Do not tear, puncture, crease, over compress or stretch during insertion. Always use the correct size Backer Rod for the particular application. Refer to the size selection chart. Do not use with hot-applied sealants or hot melt adhesives where their surface temperature is over 160 degreeF (71 degreeC).
Most shipping weights are approximate and have not been verified. If the exact weight is needed in order to determine shipping costs, and shipping costs are required in order for you to complete your order, please request this prior to submitting your order by contacting CRL Customer Service. Product images shown are of the actual product or a close representation. Colors can vary depending on your computer's video card and on how your monitor's color is adjusted.